Revision as of 04:19, 13 November 2008 (view source) WikiAdmin (Talk | contribs) ← Older edit		Revision as of 04:23, 13 November 2008 (view source) WikiAdmin (Talk | contribs) Newer edit →
Line 45:		Line 45:
	== Output  ==		== Output  ==
−	=== Analog Output Daughterboards ===	+	=== [[Analog Output Daughterboards]] ===
−	* [[DOA_AnOut1]]	+	{{AnOutDaughterboardsList}}
	=== [[Digital Output Daugterboards]] ===		=== [[Digital Output Daugterboards]] ===

---

Revision as of 04:23, 13 November 2008

PHCC Daughterboards Overview

explain Daughterboards here.

Input

• Digital
  • Switches
  • momentary contact
    • Pushbuttons
  • permanent contact
    • Flip Switches
    • Rotary Switches
      • just as rotary selectors, eg. Power Sel: APU, external Power, Engines
      • as incremental switches, eg. turning left decrements, turning right increments
  • ... and similar momentary or permanent on/off devices
  • Rotary Encoders
    • 2 bit gray code quadrature
    • mechanical
    • optical
• Analog
  • potentiometers
  • other devices with 0-5V variable output

Digital Inputs

Each PHCC Motherboard can read up to 1024 digital input channels. These inputs are available through Keymatrix Daughterboards. Each Keymatrix Daughterboard provides 64 inputs, in an 8x8 matrix. Each PHCC Motherboard allows up to 16 Keymatrix Daughterboards to be connected.

The matrix organization means that you only need 16 (instead of 128) wires from PHCC to each set of 64 switches.

Keymatrix Daughterboards

• KEY64D_PH
• KEY64D_SC35
• KEY64_251 (Strictly speaking NOT in matrix organization. Has one common wire for each input. So, there are 64+1 wires per board.)

Quadrature Rotary Decoder

Decodes quadrature encoded signals from mechanical and optical rotary encoders and makes the signals available for input to the Keymatrix Daughterboards.

• PHCC_rotdec

Analog Inputs

Analog input (0-5V) or variable-resistance devices (aka. potentiometers, rheostats) can be used as an input to the PHCC system via the 35 analog inputs on the

• PHCC_Motherboard

Output

Analog Output Daughterboards

• DOA_AnOut1

Digital Output Daugterboards

• DOA_40DO
• DOB_74595+T

Servo Controller Daughterboards

• DOA_8servo

Stepper Controller Daughterboards

• DOA_stepper_293

Aircore Controller Daughterboards

• DOA_stepper_293 (with different firmware)

LED, 7-segment displays, and other segmented displays

Segmented displays (7-segment, 14-segment, starburst, etc), LED bargraphs, as well as individual LEDs can be driven by the following controllers:

• DOA_7seg (both common anode and common cathode)
• DOA_7seg_2803 (older, common-cathode only revision of DOA_7seg)
• DOA_7seg_2981 (older, common-anode only revision of DOA_7seg)
• DOA_630_2803 (old, runs only on slower DOA clocks)
• DOA_877_4067 (old, runs only on slower DOA clocks)

LCD

see UPHCC sister project.

D'Arsonval Meter Movement

D'Arsonval meter movements, aka. galvanometers, can be controlled directly from the DOA_AnOut1 outputs.

• DOA_AnOut1

Other

USB interface

• PHCC_usb

Bus Terminator

• DOB_term (terminator for the end of the DOB bus)

Bus Repeater/Amplifier

see Bus Differential Converter.

Bus Differential Converter

• PHCC_LXLAT_DOA-dDOA (level translator DOA->differential DOA)
• PHCC_LXLAT_dDOA-DOA (level translator differential DOA -> DOA)

Testers

• PHCC_ParportTester_DOA_DOB

Non-PHCC

• THVP, a parallel port PIC microcontroller programmer (aka. PIC burner)