Difference between revisions of "Troubleshooting"
From PHCC
(Created page with "'''Mainboard:''' I. Analog inputs are "jittering": Sometimes analog inputs are jittering all the time without any reason. Help: Use jumper / bridges on every analog input, wh...") |
|||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | ||
| − | I. Analog inputs are "jittering": | + | == Mainboard: == |
| + | |||
| + | |||
| + | '''I. Analog inputs are "jittering":''' | ||
| + | |||
Sometimes analog inputs are jittering all the time without any reason. | Sometimes analog inputs are jittering all the time without any reason. | ||
| − | Help: | + | |
| + | |||
| + | ''Help:'' | ||
| + | |||
Use jumper / bridges on every analog input, which isn't in use. | Use jumper / bridges on every analog input, which isn't in use. | ||
| + | |||
Put the jumper on every pin#1 & pin#2. | Put the jumper on every pin#1 & pin#2. | ||
| − | + | ||
| − | II. Ghost-effect of inputs: | + | == Key64-Daughterboard: == |
| + | |||
| + | |||
| + | '''II. Ghost-effect of inputs:''' | ||
| + | |||
If you have connected only one switch (e.g. toggle, rotary, momentary, etc.) to | If you have connected only one switch (e.g. toggle, rotary, momentary, etc.) to | ||
| + | |||
your Key64-Daughterboard, and you use it (e.g. turn it to ON), | your Key64-Daughterboard, and you use it (e.g. turn it to ON), | ||
| + | |||
and there are more connections showing as ON, this would be called Ghost-effect. | and there are more connections showing as ON, this would be called Ghost-effect. | ||
| + | |||
It can also happen if there are more switches than only one attached . | It can also happen if there are more switches than only one attached . | ||
| + | |||
Ghosting will show closed electrical circuits - even if they aren't existent or not closed. | Ghosting will show closed electrical circuits - even if they aren't existent or not closed. | ||
| − | Help: | + | |
| + | |||
| + | ''Help:'' | ||
| + | |||
1. Check the soldering points on your Motherboard. | 1. Check the soldering points on your Motherboard. | ||
| + | |||
Sometimes two soldering points are connected by accident. | Sometimes two soldering points are connected by accident. | ||
| + | |||
2. Check your flatcables from Motherboard to Key64-Daughterboard. | 2. Check your flatcables from Motherboard to Key64-Daughterboard. | ||
| + | |||
Sometimes there are two or more wires connected by accident. | Sometimes there are two or more wires connected by accident. | ||
| + | |||
Often happens if the connector isn't is attached 100% correctly. | Often happens if the connector isn't is attached 100% correctly. | ||
| + | |||
3. Check your flatcables at Key64-Daughterboard. | 3. Check your flatcables at Key64-Daughterboard. | ||
| + | |||
Sometimes there are two or more wires connected by accident. | Sometimes there are two or more wires connected by accident. | ||
| + | |||
Often happens if the connector isn't is attached 100% correctly. | Often happens if the connector isn't is attached 100% correctly. | ||
| + | |||
4. Check your common and other connections at Key64-Daughterboard. | 4. Check your common and other connections at Key64-Daughterboard. | ||
| + | |||
Crosscheck with the wiring diagram on this page. | Crosscheck with the wiring diagram on this page. | ||
| + | |||
Are the common pins attached to the correct corresponding connection-pins? | Are the common pins attached to the correct corresponding connection-pins? | ||
| + | |||
Are your connection pins all attached correctly? | Are your connection pins all attached correctly? | ||
Latest revision as of 19:19, 21 November 2021
Mainboard:
I. Analog inputs are "jittering":
Sometimes analog inputs are jittering all the time without any reason.
Help:
Use jumper / bridges on every analog input, which isn't in use.
Put the jumper on every pin#1 & pin#2.
Key64-Daughterboard:
II. Ghost-effect of inputs:
If you have connected only one switch (e.g. toggle, rotary, momentary, etc.) to
your Key64-Daughterboard, and you use it (e.g. turn it to ON),
and there are more connections showing as ON, this would be called Ghost-effect.
It can also happen if there are more switches than only one attached .
Ghosting will show closed electrical circuits - even if they aren't existent or not closed.
Help:
1. Check the soldering points on your Motherboard.
Sometimes two soldering points are connected by accident.
2. Check your flatcables from Motherboard to Key64-Daughterboard.
Sometimes there are two or more wires connected by accident.
Often happens if the connector isn't is attached 100% correctly.
3. Check your flatcables at Key64-Daughterboard.
Sometimes there are two or more wires connected by accident.
Often happens if the connector isn't is attached 100% correctly.
4. Check your common and other connections at Key64-Daughterboard.
Crosscheck with the wiring diagram on this page.
Are the common pins attached to the correct corresponding connection-pins?
Are your connection pins all attached correctly?